OMX 333DC, Programmable Isolated DC Voltmeter and Ammeter
Model range OMX 333 are simple DIN rail mountable programmable signal conditioners. The range consists of UNI, DC, PWR and UQC versions. Type OMX 333UNI is a multifunction device which allows the selection from 8 inputs easily configurable in...
Features:
- Programmable Isolated Transmitters
- DC Voltmeter and ammeter
- Teach- In, Digital Filter, Tare
- Output: 0/4...20 mA/0...5 mA/0...2/5/10 V/10V
- Power Supply 10...30 V AC/DC
- Option: Comparators, Data Output, USB Interface
- Isolated
- Accuracy: ±0,15 % of range (for 20 meas./s)
- DIN Rail Mount
- Rating: IP20
Manufacturer: Orbit Merret
Quote
Datasheet
Description
Specifications
Downloads
Similar Products
OMX 333DC - Description
Model range OMX 333 are simple DIN rail mountable programmable signal conditioners. The range consists of UNI, DC, PWR and UQC versions. Type OMX 333UNI is a multifunction device which allows the selection from 8 inputs easily configurable in the instrument's menu. OMX 333DC a OMX 333PWR are versions used for measurement of higher DC and AC voltage and current. The instrument is based on a single-chip micro controller with a 12bit A/D and D/A convertor which provides high accuracy, stability and ease of use. OMX 333UQC version is a universal counter/frequency meter.
Instrument can be controlled by two push buttons and a DIP switch located on the front panel. When frequent change of settings are needed, we recommend the use of OM Link interface which in conjunction with free control SW allows for modification and storage of all instrument's settings as well as for the firmware upload from a PC using OM Ling cable.
The above mentioned SW can also be used for visualization and archiving of measured values from a number of instruments via the RS 485 line.
All instrument's settings are stored in an instrument's EEPROM memory (even after powered-off)
Instrument can be controlled by two push buttons and a DIP switch located on the front panel. When frequent change of settings are needed, we recommend the use of OM Link interface which in conjunction with free control SW allows for modification and storage of all instrument's settings as well as for the firmware upload from a PC using OM Ling cable.
The above mentioned SW can also be used for visualization and archiving of measured values from a number of instruments via the RS 485 line.
All instrument's settings are stored in an instrument's EEPROM memory (even after powered-off)
OMX 333DC - Specifications
| Interface | USB |
| Input Type | ±25 V DC |
| ±50 V DC | |
| ±100 V DC | |
| ±200 V DC | |
| ±400 V DC | |
| ±1 A | |
| ±5 A | |
| # of Inputs | 1 |
| Output Type | 0 - 2 V DC |
| 0 - 5 V DC | |
| 0 - 10 V DC | |
| ±10 V DC | |
| 0 - 5 mA | |
| 0 - 20 mA | |
| 4 - 20 mA | |
| RS-485 | |
| Isolation | Yes |
| Supply Power | 10 - 30 V DC |
| 10 - 30 V AC | |
| IP Rating | IP 20 |
OMX 333DC - Downloads
OMX333 Datasheet |
OMX 333DC - Similar Products
- Process Monitor, for process signals
- Extremely fast digital transducer
- Isolated Versions Available
- USB Connectivity for easy calibration
- DAQ Mode with a measuring rate - up to 7500 measurements per second
- 2 Button teach-in for Potentiometer
- Teach-in, allows easy setting of both min. and max. of the measuring range
- Output: 4…20 mA/0…10 V
| Interface | USB |
| Input Type | 0 - 10 V DC, 0 - 20 mA, 4 - 20 mA |
| # of Inputs | 1 |
| Output Type | 0 - 10 V DC, 4 - 20 mA, RS-485 |
| Excitation | 15 V DC, 24 V DC |
| Isolation | Yes |
- Simple DIN rail mountable programmable signal convertors.
- Multifunction input UNI (DC, PM, RTD, T/C, DU)
- TEACH-IN, DIGITAL FILTER, TARE
- Isolated, 10-30 V AC/DC
- Accuracy: ± 0,15 % of range (for 20 meas./s), ± 0,3 % of range PWR, T/C, ± 0,05 % of value UQC
- DIN Rail Mount
- IP20 rating
| Interface | USB |
| Input Type | ±30 mV DC, ±60 mV DC, ±1 V DC, ±2 V DC, ±5 V DC, ±10 V DC, ±20 V DC, ±40 V DC, ±80 V DC, 4 - 20 mA, ±5 mA, ±20 mA, ±90 mA, ±180 mA, Potentiometer, Resistance, Thermocouple, RTD |
| # of Inputs | 1 |
| Output Type | 0 - 2 V DC, 0 - 5 V DC, 0 - 10 V DC, ±10 V DC, 0 - 5 mA, 0 - 20 mA, 4 - 20 mA, RS-485 |
| Isolation | Yes |
| Supply Power | 10 - 30 V DC, 10 - 30 V AC |
- Programmable Isolated Transmitters
- Universal Counter
- Teach- In, Digital Filter, Tare
- Output: 0/4...20 mA/0...5 mA/0...2/5/10 V/10V
- Power Supply 10...30 V AC/DC
- Option: Comparators, Data Output
- Isolated
- Accuracy: ±0,05 % of value UQC
| Interface | USB |
| Input Type | Frequency, Counter |
| # of Inputs | 1 |
| Output Type | 0 - 2 V DC, 0 - 5 V DC, 0 - 10 V DC, ±10 V DC, 0 - 5 mA, 0 - 20 mA, 4 - 20 mA, RS-485 |
| Isolation | Yes |
| Supply Power | 10 - 30 V DC, 10 - 30 V AC |
- Programmable Isolated Transmitters
- AC Voltmeter and Ammeter
- AC Network Analyser
- Teach- In, Digital Filter, Tare
- Output: 0/4...20 mA/0...5 mA/0...2/5/10 V/10V
- Power Supply 10...30 V AC/DC
- Option: Comparators, Data Output
- Isolated
| Interface | USB |
| Input Type | 0 - 60 mV AC, 0 - 300 mV AC, 0 - 10 V AC, 0 - 120 V AC, 0 - 250 V AC, 0 - 450 V AC, 0 - 1 A AC, 0 - 5 A AC |
| # of Inputs | 1 |
| Output Type | 0 - 2 V DC, 0 - 5 V DC, 0 - 10 V DC, ±10 V DC, 0 - 5 mA, 0 - 20 mA, 4 - 20 mA, RS-485 |
| Isolation | Yes |
| Supply Power | 10 - 30 V DC, 10 - 30 V AC |
- Cost Effective Measurement for Strain Gauge, Potentiometer, Voltage and Current
- Transmitter for Linear Potentiometers
- Isolated Versions Available
- USB Connectivity for easy calibration
- DAQ Mode with a measuring rate - up to 7500 measurements per second
- 2 Button teach-in for Potentiometer
- Teach-in, allows easy setting of both min. and max. of the measuring range
- Output: 4…20 mA/0…10 V
| Interface | USB |
| Input Type | Potentiometer |
| # of Inputs | 1 |
| Output Type | 0 - 10 V DC, 4 - 20 mA, RS-485 |
| Excitation | 2.5 V DC |
| Isolation | Yes |