BeanDevice AN-mV, Wireless milli-Volt Analog Data Acquisition System
- Wireless analog data acquisition system with low voltage inputs (±20 mV), 4 analog channels
- High measurement accuracy: < 0.08%, 16-bit of resolution
- Maximum sampling rate: 400 samples per second
- Watertight (IP65 | Nema 4) aluminum casing
- TimSync function: Time-synchronization over the Wireless Sensor Networks with an accuracy of ±2.5 ms
- Maximum Radio Range: 650 m (L.O.S)
The BeanDevice® AN-mV is a wireless data logger with analog voltage inputs (±20mV). Special care is taken in the analog signal conditioner design with an accuracy of ±0.4% (FS) and a dynamic range of 16-bits.
This sensor is directly powered by a high accuracy and adjustable DC/DC converter integrated inside the device. The excitation voltage is remotely configurable through the BeanScape® (4.5 to 20V).
Characterized by a watertight (IP65) and small (146.05 mm x 65.5 mm x 33.5mm) aluminum enclosure, an ultra-low power (30 µA in sleeping mode), an integrated data logger that can store up to 1 million data logs, as well as a maximum wireless range of 1 Kilometer (L.O.S.), this wireless device is well suited for all types of industrial applications.
The outstanding TimeSync® function allows to reach a time-synchronization of ±2.5ms over the wireless sensor networks. It contributes to enhance user experience about data fusion and modal analysis.
Users looking for a quick and easy integration with a third party software, have choice between ModBus TCP/RTU/ASCII protocol available on our BeanGateway® or OPC DA available on our BeanScape® (Premium+ & Cloud versions only).
BeanScape 2.4GHz - How to use the Alarm - Data Acquisition Mode: https://youtu.be/XxWJT7A9ntY
BeanScape 2.4GHz - How to use Low Duty Cycle Data Acquisition Mode: https://youtu.be/TGDBPrFeO_8
Beanscape 2.4GHz - How to perform streaming in Data Acquisition Mode: https://youtu.be/OVVpj0V8svU
How to switch between Standard and Expert HMI View : https://youtu.be/HFtu7HapIeI
| Input Types | Strain Gauge |
| Vdc | |
| No. of Inputs | 2-20 |
| Output | Ethernet |
The BeanDevice® AN-mV is suitable for the following applications:
- Remote Monitoring of Tank Weights
- Bridge Strain & Stress Monitoring
- Built-in Test Equipment
- Condition Monitoring of Structures & Buildings
- Structural Health Monitoring (SHM)
BeanDevice AN-mV Datasheet |
BeanDevice AN-mV User Manual Manual |
BeanDevice AN-mV Mechanical Drawing Drawings |
TN-RF-008 Data acquisition modes available on the BeanDevice Tech Note |
AN-RF-006 How to extend your wireless range App Note |
UM-RF-01, SmartSensor wireless accelerometer inclinometer and shock sensor Manual |
UM-RF-02, ProcessSensor-Wireless DAQ Manual |
UM-RF-03, EcoSensor Wireless Sensor for Environment Manual |
- 16 bit resolution A/D
- Simultaneous Sampling of all Channels
- Bandwidth up to 24kHz for the 4 Channel System
- Radio Telemetry Transmission
- Uses 1 Data Transmission Module, with up to 16 Input Modules
- Water Resistant - IP65 modules
- Powered from 7-30 Vdc
| Input Types | Strain Gauge, Vdc, Temperature, IEPE-ICP |
| No. of Inputs | 2-20 |
| Output | Analog, Ethernet |
- Waterproof (IP66, IP67)
- Ideal for brake testing due to excellent heat dissipation
- Removable stator for convenient balancing of wheels
- Online zeroing - system is ready to measure after three turns of the wheel
- Measurement range: Fx, Fz = ±45 kN, Fy = ±25 kN, Mx, My, Mz = 8.75 kNm
- Angular resolution 0.072°
- Working temperature range (sensor): -40°C to +150°C
- Convenient parameterization with software RemusLAB
| Input Types | Strain Gauge |
| No. of Inputs | 2-20 |
| Output | Analog, Ethernet, CANbus |
- Measurement of driving and breaking torques
- sealed IP67 (waterproof)
- Transmitter electronics integrated in sensor
- My = 3.000 Nm (4.500 Nm optional)
- Power supply: rechargeable battery (approx. 50 h operating time)
- Working temperature (Sensor): -10°C … +60°C
- Programmable amplifiers with autozero function
- Convenient parameterization by RemusLAB or webbrowser
| Input Types | Strain Gauge, Temperature |
| No. of Inputs | 2-20 |
| Output | Analog, Ethernet, CANbus |
- Static & Dynamic measurements up to 24,000 Hz
- 2 to 64 channel systems
- Inputs for Strain Gauges, Temperature, ICP sensors or Voltages
- 4 Vdc Excitation & Gains selectable, 125, 250, 500, 1000 or 2000
- 16 bit ADC, simultaneous sampling
- Full software programmable & Auto Zero calibration
- Inductive or battery powered
- Rugged, water proof housing
| Input Types | Strain Gauge, Vdc, Temperature |
| No. of Inputs | 8 +, 2-20 |
| Output | Analog |
- Steering torque range ±100 Nm or ±200 Nm
- Steering angle range ±1474,56°
- Rotational velocity range ±1000°/sec
- Acceleration in x, y, z (optional)
- Rotational acceleration (optional)
- CAN and analog output
- Online monitoring of all channels in physical values
- Inductive power supply by control unit
| Input Types | Strain Gauge, Vdc |
| No. of Inputs | 2-20 |
| Output | Analog, CANbus |